Cart
0
0.00 €
Mercedes Sprinter Camper Box – Removable Modular Camper Conversion Kit
Transform your Mercedes Sprinter Panel Van, Crew or Tourer into a fully equipped camper in minutes with our self-install, removable furniture system, designed for compatible L1–L4 and H1–H3 layouts without permanent vehicle modifications.
Mercedes Sprinter Camper Conversion for Panel Van, Crew and Tourer Models
Removable New Design Camper Furniture for Compatible Sprinter L1–L4 and H1–H3 Vans
Transform your Mercedes Sprinter into a practical camper van with a removable, self-install New Design camper furniture kit created for travel, vanlife and everyday vehicle use.
The central furniture module is shared across our large-van range, while the side modules and extensions are adapted when necessary to the Sprinter's wheel arches, interior trim and available width. Before manufacturing, we confirm the model year, wheelbase, roof height, bulkhead, seating arrangement and available anchoring points.
The Mercedes Sprinter camper kit can include:
✅ A folding camper bed approximately 185–190 cm long and 170–180 cm wide in compatible full-width configurations.
✅ A made-to-measure dark-grey modular mattress pack, included with every furniture material.
✅ A rear pull-out kitchen drawer prepared for a compatible Campingaz-style stove.
✅ A multi-height table for dining or lounge use inside the van and as a standalone camping table outside.
✅ XL storage trunks and compartments for food, clothes, water, camping equipment or a portable toilet.
✅ Side modules adapted to compatible wheel-arch areas, extending the sleeping surface and providing additional storage.
✅ A dedicated compartment or optional sliding support for the recommended Coolzone 35L compressor fridge.
✅ A reinforced folding structure suitable for compatible layouts with or without rear seats.
When folded, the removable Mercedes Sprinter camper furniture remains compactly stored in the rear area, helping the van stay practical for work, passenger transport and everyday use.
In compatible Crew or Tourer layouts, selected rear seats can remain usable. The exact number of seats depends on the original seating arrangement, body length and chosen furniture configuration.
When installed without permanent structural modifications, the system is normally treated as correctly secured cargo rather than a fixed camper conversion. It must always be properly secured while travelling, and local requirements should be checked according to the country, vehicle category and accessories installed.
👉 Buy the Mercedes Sprinter camper furniture kit with dark-grey mattress pack included:
Mercedes Sprinter Camper Box – Removable Camper Kit with Mattress Pack
Mercedes Sprinter Generations and Camper Kit Compatibility
Removable Camper Furniture Adapted to Sprinter Panel Van, Crew and Tourer Layouts
Our removable camper furniture system can be adapted to compatible vehicles from the three main Mercedes Sprinter generations:
First generation: 1995–2006
Second generation: 2006–2018
Third and current generation: 2018–present
Compatible Mercedes eSprinter layouts, subject to individual vehicle confirmation
The eSprinter is the electric version of the current Sprinter platform rather than a separate fourth generation. Its interior equipment and available anchoring points must be checked before manufacturing.
Mercedes Sprinter body sizes are commonly identified as L1, L2, L3 or L4, with roof heights described as H1, H2 or H3. However, the combinations available vary according to the generation, model year and country.
Our principal central furniture module is designed for large vans and is used across the range. When necessary, we adapt the side modules, wheel-arch covers and bed extensions to the specific Mercedes Sprinter interior.
Before manufacturing your Mercedes Sprinter camper furniture kit, we confirm:
Model year and generation
Body length or wheelbase
Roof height
Panel Van, Crew or Tourer configuration
Bulkhead and rear-seat arrangement
Interior trim and wheel-arch covers
Rear electrical or climate-control equipment
Available factory anchoring points
This verification ensures that the removable furniture, sleeping platform and storage modules are correctly adapted to the actual interior of your Mercedes Sprinter.
Mercedes Sprinter Removable Camper Kit for Work and Passenger Vans
Fast, Self-Install Camper Furniture for Compatible 3, 5 and 6-Seat Layouts
The Mercedes Sprinter camper furniture kit provides a fast and reversible way to convert a compatible work or passenger van into a practical camper setup.
The system is removable and modular, allowing selected 3, 5 or 6-seat configurations to remain usable depending on the original seating arrangement, wheelbase and chosen furniture layout.
When folded, the complete camper module — including the custom-made mattress pack — remains compactly stored in the rear area. This helps maintain:
Rear visibility in compatible windowed versions
A clean, factory-style interior
Camping equipment organised and protected
Secure attachment using suitable factory anchoring points
Practical daily use as a work or passenger vehicle
When installed without permanent structural modifications, the furniture is normally treated as correctly secured cargo rather than a fixed camper conversion. It must always be properly secured while travelling, and applicable requirements should be checked according to the country, vehicle category, inspection authority and accessories installed.
This reversible system is especially practical for customers who use their Mercedes Sprinter professionally during the week and as a camper for weekends, holidays or long-distance travel.
Materials and Prices for the Mercedes Sprinter Camper Furniture Kit
Four Furniture Options with Dark-Grey Modular Mattress Pack Included
The Mercedes Sprinter camper kit is available in four materials. Every option includes the custom-made dark-grey modular mattress pack in the indicated price.
White Laminated MDF – €850
Economical finish for workshop collection
12 mm laminated board
Clean white appearance
Most economical material
Suitable for occasional camper use
Available only for collection from our workshop
Consideration:
MDF is more sensitive to moisture and impacts than the plywood alternatives, so it is not available for palletised delivery.
Natural Pine Phenolic Plywood – €900
Natural wood grain and moisture-resistant construction
15 mm phenolic plywood
Warm natural pine appearance
Good structural resistance
Treated to withstand normal camper humidity and condensation
Excellent balance between price, strength and natural finish
Consideration:
Its visible wood grain and tone vary naturally from one board to another.
Cream-White Poplar Plywood – €925
Lightweight furniture with a bright interior finish
15 mm lightweight plywood
Light cream-white colour
Helps create a brighter interior
Strong and easy to handle
Particularly suitable for large removable modules
Consideration:
Poplar has a softer surface than the HPL-type coachbuilder board and can mark under concentrated pressure from hard or sharp objects.
Dark HPL-Type Coachbuilder Plywood – €950
Maximum resistance and easy-clean professional finish
15 mm high-resistance plywood
Very dark brown, almost black appearance
Smooth face combined with a non-slip face
Highly resistant to moisture, intensive use and cleaning
Recommended for frequent travel and professional applications
Consideration:
It is heavier than the other plywood options, although it remains appropriate for removable camper furniture.
All four versions use the same New Design furniture concept, incorporating the improvements developed through our experience manufacturing removable camper kits. The most suitable material depends on the required weight, finish, durability and whether the kit will be collected or delivered.
Camper Furniture Kit Materials – Differences, Properties & Durability
Mercedes Sprinter Camper Box – 35L Slide-Out Fridge Drawer Example
Mercedes Sprinter Camper Furniture Features and XL Storage Layout
Detailed Breakdown of the Modular, Removable Mercedes Sprinter Camper Box
The Mercedes Sprinter camper furniture kit combines the principal functions needed for sleeping, cooking, dining and storing equipment in a modular system that remains completely removable.
It can be adapted to compatible Sprinter body sizes commonly described as L1, L2, L3 or L4 and H1, H2 or H3, subject to confirmation of the model year, interior layout, wheel arches, trim and available anchoring points.
🔧 Custom Slide-Out Kitchen Drawer
The rear of the Sprinter camper kit includes a custom pull-out kitchen drawer prepared for a compatible Campingaz-style single-burner stove or a larger model when the available space allows it.
Behind the kitchen drawer is an independent top-opening storage trunk, suitable for:
Cookware and utensils
Food and bottles
Camping accessories
Frequently used travel equipment
The stove and cooking accessories must be stored securely before travelling and should only be used with suitable ventilation and safety precautions.
🛋️ Multi-Height Indoor and Outdoor Table
The central module incorporates a multi-height table that can be used in several positions:
Indoor dining mode
Lounge or sofa mode
Hammock-style seating mode
Outdoor camping or picnic table
Its modular design works together with the folding furniture and mattress sections, allowing the interior to change between dining, relaxation and sleeping configurations.
📦 Dual-Access Storage for Fridge, Water and Camping Equipment
The left side of the furniture can include two high-capacity storage compartments with top and front access, depending on the selected configuration.
Rear Compartment – Compressor Fridge Storage
The rear compartment can be prepared for a compatible Coolzone 35L compressor fridge or another fridge with suitable dimensions.
Depending on the furniture layout, the fridge can be positioned:
Inside the dedicated top-access compartment
On an optional front sliding support
Final compatibility must be confirmed using the exact dimensions of the selected fridge.
Front Compartment – Shower, Water or Portable Toilet Storage
The front-access compartment is suitable for storing:
A portable 12V outdoor shower
A removable water container
Camping equipment
A portable toilet
Shoes or frequently used accessories
We normally recommend the double-opening configuration with top and front access, as it provides greater usable volume and easier access than a fully enclosed drawer.
🛏️ Wheel-Arch Side Modules and Full-Width Sleeping Area
Compatible configurations can include two side modules adapted to the Mercedes Sprinter wheel arches and interior trim.
These modules help extend the sleeping platform across the available rear width while adding top-opening storage for:
Bedding and blankets
Clean or used clothing
Shoes and personal belongings
Lightweight travel equipment
The dimensions of the side modules are adapted when necessary because the wheel arches, wall trim and usable interior width vary between Sprinter generations and layouts.
🗄️ Optional Double-Drawer Configuration
A double-drawer layout is available as an optional configuration, although we generally recommend the larger open storage trunks because they provide:
Greater usable internal volume
Lower overall weight
Fewer structural elements inside the furniture
Better long-term durability
Easier access to bulky equipment
When drawers are requested, reinforced guides can be fitted according to the required load and furniture configuration.
🎨 Furniture Finishes and Dark-Grey Mattress Pack
The furniture is available in different finishes, including the bright cream-white poplar option, natural pine phenolic plywood and dark HPL-type coachbuilder plywood.
All finishes are combined with the included dark-grey modular mattress pack, creating a neutral and practical interior suitable for both professional and recreational use.
The New Design designation refers to the furniture system, which incorporates the improvements developed throughout our experience manufacturing removable camper kits.
📐 Mercedes Sprinter Camper Box Dimensions
Measurements vary according to the Sprinter generation, wheelbase, interior trim, wheel arches, installed seats and selected side modules.
Typical dimensions are:
Main furniture width: approximately 170 cm
Full sleeping width: approximately 170–180 cm in compatible full-width layouts
Main module depth: approximately 120 cm
Extended bed length: approximately 185–190 cm
Side modules: adapted to the vehicle where required
A transverse sleeping arrangement is only possible in selected vehicles with sufficient measured wall-to-wall width and must be assessed individually.
🛏️ Custom Modular Mattress Pack Included
Every Mercedes Sprinter camper furniture kit includes a custom-made dark-grey modular mattress pack in the price.
Its separate sections are designed to provide:
Easy access to the storage compartments
Dining mode
Lounge or sofa mode
Hammock-style seating mode
A stable full-bed configuration
Compact storage when the furniture is folded
The final mattress shape and dimensions are adapted to the confirmed furniture and vehicle configuration, helping create a comfortable sleeping surface with minimal separation between the individual sections.
Mercedes Sprinter Camper Kit Installation: Quick Setup, Secure Fastening and Daily Use
Quick Removable Setup: Switch from Work or Passenger Use to Camper Mode in Minutes
The Mercedes Sprinter camper furniture kit is designed for quick, reversible installation without permanent structural modifications.
Depending on the confirmed vehicle layout, the furniture can be installed, deployed and folded away without tools, allowing the Sprinter to alternate between daily work, passenger transport and camper use.
Secure Fastening and Driving Stability: Supports Stored Without Movement or Rattling
The furniture includes dedicated storage for the table leg and folding bed supports, keeping the separate components organised and secured while travelling.
The sleeping platform distributes the load through two principal support sections:
Rear main furniture module – the primary load-bearing structure positioned in the rear of the van.
Front folding bed platform – supported either by the folded rear seats in compatible passenger layouts or by reinforced folding legs when the van is used without rear seats.
This two-part structure is designed to provide:
A stable sleeping platform
Controlled weight distribution
Protection for compatible folded seats and interior trim
Reduced movement and noise while travelling
Reliable support during repeated use
The furniture must always be correctly secured using suitable anchoring points or the fastening method confirmed for the specific vehicle.
Daily Use with the Camper Module Folded
When not deployed as a bed, the furniture and dark-grey modular mattress pack remain compactly stored in the rear area.
This helps maintain:
Practical access to the rear storage compartments
Rear visibility in compatible windowed versions
An organised, factory-style interior
Daily use as a professional or passenger vehicle
Camping equipment stored discreetly inside the van
Installation Heights for Cargo and Passenger Sprinter Layouts
The furniture height is selected according to the interior configuration and the seats that will remain in the vehicle.
40, 44 or 48 cm: typically used in cargo layouts without rear seats, depending on the required storage capacity and interior headroom.
Higher custom configurations: used when the folding platform must align with retained or folded rear seats.
The final height is confirmed after checking the actual seat-folding level and interior measurements. This prevents pressure points and ensures that the sleeping surface remains properly aligned.
Detailed Mercedes Sprinter Compatibility Check
Before manufacturing, we confirm:
Generation and model year
Body length or wheelbase
Roof height
Panel Van, Crew or Tourer configuration
Bulkhead and rear-seat arrangement
Number of seats to be retained
Interior trim and wheel-arch covers
Rear climate-control or electrical equipment
Available anchoring points
Required furniture and bed height
Body and roof designations such as L1–L4 and H1–H3 vary according to the Sprinter generation and market. Compatibility and final measurements are therefore confirmed individually before production.
When used as a removable system without permanent structural modifications, the furniture is normally treated as correctly secured cargo rather than a fixed camper conversion. Requirements vary by country, vehicle category and installed accessories, so the applicable local regulations should always be checked.
Compatible Accessories for the Mercedes Sprinter Camper Kit
Complete Your Mercedes Sprinter Camper Conversion with Practical Removable Equipment
The Mercedes Sprinter Camper Furniture Kit can be combined with compatible accessories for cooking, water storage, refrigeration, privacy, electrical autonomy and year-round comfort.
Compatibility depends on the Sprinter generation, model year, body length, roof height, interior layout and available space. Before ordering, we recommend confirming the exact vehicle configuration.
🚰 Foldable Camper Sink with Drain Plug
A compact washing solution designed to work with a portable 12V shower while occupying considerably less space than a conventional fixed sink.
🚿 12V Outdoor Camper Shower with Portable 20L Water Tank
Suitable for showering, washing dishes, cleaning equipment or rinsing bicycles outside the vehicle.
https://www.kitmueblecamper.com/p/12v-outdoor-camper-shower-20l-portable-water-tank/
🔥 Custom Campingaz 1-Burner Stove
Compatible with the made-to-measure rear kitchen drawer of the Mercedes Sprinter camper furniture kit.
https://www.kitmueblecamper.com/p/custom-campingaz-1-burner-stove-for-our-camper-furniture/
🧊 Coolzone 35L Compressor Fridge
Our recommended compressor fridge for compatible storage compartments and optional sliding fridge supports.
https://www.kitmueblecamper.com/p/coolzone-35l-compressor-fridge-lg-compressor-recommended-for-our-camper-furniture-kits/
🌡️ Nine-Layer Thermal Blackout Covers
Designed to improve privacy and thermal insulation inside compatible Mercedes Sprinter Panel Van, Crew and Tourer layouts.
https://www.kitmueblecamper.com/p/blackout-shades-thermal-insulation-for-camper-vans1/
🚲 2+1 Modular Camper Furniture Configuration
This configuration allows one section of the furniture to be removed when additional space is required for bicycles, surfboards, work equipment or larger luggage.
https://www.kitmueblecamper.com/p/en-modalidad-2-1/
🔋 Auxiliary Battery with Optional Inverter
Provides independent power for the compressor fridge, lighting, USB connections, 12V accessories and compatible 230V equipment.
https://www.kitmueblecamper.com/en/camperizar-furgoneta/bateria-camper/
🚰 Independent Camper Sink and Kitchen Unit
A separate removable furniture module with clean- and waste-water tanks, storage compartments, drawers and a 12V water pump. It can be combined with the rear Mercedes Sprinter camper box when the available layout allows.
https://www.kitmueblecamper.com/p/camper-sink-kitchen-unit-compatible-with-camper-furniture-kits/
🔥 Stationary Heater with Digital Controller
A stationary heating system may be added subject to vehicle compatibility, available installation space and applicable regulations.
https://www.kitmueblecamper.com/p/en-calefaccion-estacionaria/
Product availability and specifications should always be checked on the corresponding product page. Fixed electrical systems, stationary heaters and other permanent installations may require professional installation, certification or approval depending on the vehicle and applicable local regulations.
How to Order Your Mercedes Sprinter Camper Kit with Accessories
Choose the required furniture configuration and add the compatible accessories individually to your order.
For compatibility advice, tell us your Mercedes Sprinter model year, body length or wheelbase, roof height, interior layout and the number of seats you want to retain.
📲 WhatsApp:
Mercedes Sprinter Camper Kit Installation: Quick Setup, Secure Fastening and Daily Use
Quick Removable Setup: Switch from Work or Passenger Use to Camper Mode in Minutes
The Mercedes Sprinter Camper Furniture Kit is designed for quick, reversible installation without fixed furniture or permanent structural modifications.
Depending on the confirmed vehicle layout, the furniture can be positioned, secured, deployed and folded away without tools, allowing the Sprinter to alternate between daily work, passenger transport and camper use.
Secure Fastening and Driving Stability: Supports Stored Without Movement or Rattling
The furniture includes dedicated storage for the table leg and any removable bed-support legs supplied with the selected configuration. This keeps the separate components organised and secured while travelling.
The sleeping platform distributes the load through two principal support sections:
Rear main furniture module – the primary structural and load-bearing section positioned in the rear of the vehicle.
Front folding bed platform – supported either by compatible folded rear seats or by reinforced folding support legs when the vehicle is used without rear seats.
This two-part structure is designed to provide:
A stable sleeping platform
Controlled weight distribution
Protection for compatible folded seats and interior trim
Reduced movement and unwanted noise
Reliable support during camper use
The furniture must always be secured using suitable anchoring points and the fastening method confirmed for the vehicle.
Daily Use with the Camper Module Folded
When not deployed, the New Design camper furniture and its custom-made dark-grey modular mattress pack remain compactly stored inside the rear cargo area.
This configuration helps preserve:
Practical access to the rear area
Rear visibility in compatible windowed versions
A clean, discreet interior appearance
Everyday professional or passenger use
Camping equipment organised inside the vehicle
Installation Heights for Cargo and Passenger Sprinter Layouts
Depending on the confirmed interior configuration, the Mercedes Sprinter camper furniture can be manufactured at approximately:
40 cm
44 cm
48 cm
In layouts without rear seats, the height is selected according to the required under-bed storage, available headroom and intended use.
When compatible rear seats are retained, a higher customised configuration may be required to align the sleeping platform with the actual folded-seat height.
Detailed Mercedes Sprinter Compatibility Check
The central furniture module follows our proven large-van design. The lateral modules, extensions and support arrangement may be adapted to the usable interior width of the Mercedes Sprinter.
Before manufacturing, we confirm:
Model year and vehicle generation
Body length or wheelbase
Roof height
Panel Van, Crew or Tourer configuration
Bulkhead, floor and interior lining
Original seating arrangement
Number of seats to retain
Wheel arches and plastic trim
Rear climate-control or electrical equipment
Available and compatible anchoring points
Required furniture height
Selected sleeping configuration
Body-size terminology such as L1, L2, L3, L4, H1, H2 and H3 can vary according to generation and market, so compatibility is always confirmed using the actual vehicle specifications.
When installed as a removable system without permanent structural modifications, the furniture is normally treated as securely fastened cargo rather than a fixed camper conversion. It must always be correctly secured while travelling. Requirements vary by country, vehicle category, inspection authority and installed accessories, so the applicable local regulations should be checked.
FAQ – Mercedes Sprinter Camper Box & Removable Conversion Kit
Which Mercedes Sprinter versions are compatible with the removable camper kit?
The furniture can be adapted to compatible Mercedes-Benz Sprinter Panel Van, Crew and Tourer passenger layouts, including body sizes commonly described as L1, L2, L3 or L4 and H1, H2 or H3. Available combinations vary by generation and market, so before manufacturing we confirm the model year, body length or wheelbase, roof height, interior trim, bulkhead, seating arrangement and available anchoring points.
What are the bed dimensions of the Mercedes Sprinter camper conversion?
Depending on the confirmed configuration, the sleeping area is approximately 185–190 cm long and approximately 170–180 cm wide in a compatible full-width layout. Final dimensions depend on the body configuration, interior trim, wheel arches, installed seats and selected side modules or extensions.
What is included with the Mercedes Sprinter camper furniture kit?
The kit can include a removable folding bed structure, a custom-made dark-grey modular mattress pack, a rear kitchen drawer prepared for a compatible Campingaz-style stove, a multi-height indoor and outdoor table, XL storage compartments and the required folding supports. Exact equipment depends on the selected configuration.
Does the removable Mercedes Sprinter camper kit require homologation?
When installed as a removable system without permanent structural modifications, the furniture is normally treated as securely fastened cargo rather than a fixed camper conversion. It must always be correctly secured while travelling. Requirements vary by country, vehicle category, inspection authority and installed accessories, so the applicable local regulations should be checked.
Which fridge and kitchen accessories are compatible with the Mercedes Sprinter camper kit?
The Coolzone 35L compressor fridge is recommended for compatible layouts and can be placed in a dedicated compartment or on an optional sliding support. The kit can also be combined with a removable sink and kitchen unit, subject to the available space and the confirmed vehicle configuration.
Customer Reviews of Kit Muebles Camper
Rated 4.9 Out of 5 Based on 51 Customer Reviews
⭐ Overall customer rating: 4.9/5 from 51 reviews
Our customers value the practicality, strength and everyday usability of our removable camper furniture systems.
Many reviews highlight the quick setup, generous storage, comfortable custom-made mattress pack and the ability to alternate between everyday vehicle use and camper mode.
Google Reviews from Spain and France
Read customer experiences and view photographs of real camper furniture installations through our Google Maps profiles:
🇪🇸 Madrid – Arganda del Rey
https://maps.app.goo.gl/YR3S8WCe1pqdb1Xb7
🇪🇸 Barcelona – Tordera
https://maps.app.goo.gl/bHjBo51GtmkenoCa7
🇪🇸 Seville – Écija
https://maps.app.goo.gl/13MZuMieqKebSP9w6
🇫🇷 France – Narbonne / Argeliers Area
https://maps.app.goo.gl/6HwG9uanwFepyD6cA
Order Your Mercedes Sprinter Camper Furniture Kit
Confirm Compatibility and Choose the Right Large-Van Configuration
Transform your compatible Mercedes Sprinter into a practical camper with a removable furniture system designed for travel, camping and everyday vehicle use.
The available configuration can include:
✅ New Design removable camper furniture
✅ A sleeping area approximately 185–190 cm long and 170–180 cm wide, depending on the confirmed layout
✅ Custom-made dark-grey modular mattress pack included
✅ Rear pull-out kitchen drawer
✅ Multi-height indoor and outdoor table
✅ XL storage compartments
✅ Central large-van furniture module with lateral modules adapted when required
✅ Configurations for compatible Panel Van, Crew and Tourer layouts
🟢 Buy the Mercedes Sprinter Camper Furniture Kit with Mattress Pack Included:
🟢 Add the Independent Camper Sink and Kitchen Unit:
https://www.kitmueblecamper.com/p/camper-sink-kitchen-unit-compatible-with-camper-furniture-kits/
📲 Request compatibility advice or a customised configuration through WhatsApp:
Thanks Be to God
Every Project, Journey and Opportunity Begins with Him
Thank you for trusting Kit Muebles Camper.
Above all, thanks be to God for every project, every journey and every opportunity to serve.
"I can do all things through Christ who strengthens me." — Philippians 4:13
Juan Jose,
